Follow these instructions to assemble the Clarius Ultrasound Cart – Tryten. Please refer to Tryten's instruction manual for further instructions.
1) Assemble Tryten’s Clarius Ultrasound Cart
Follow Tryten’s instructions to assemble the ( Download PDF instructions here)
1. Open the Shipping Box
- Open the shipping box and remove the base assembly.
- Extract the hardware pack.
- Remove the Pole assembly from the packaging.
2. Prep the Pole assembly
- Remove 4 screws and split washers from Pole assembly using the 3/16-inch hex L key from the hardware pack.
3. Assemble the Pole assembly
- Assemble the Pole assembly to the base using the 4 screws and split washers that came with the Pole assembly using the 3/16-inch hex L key from the hardware pack.
2) Clarius Configuration
Once you have assembled the Tryten Nova Pro Cart - it would look similar to the picture below:
1. Remove the frontal Power Box and channel covers
- Open the Power Box, located in the center of the pole. Turn the unit around to the back to locate 2 screws at the back of the Power Box. Using your Torx Security L-key, loosen and remove the 2 screws located on the back of the Power Box. Keep screws in a safe place.
The Power Box cover should now easily slide off by lifting it up or down.
- Using the 5/32’’ Allen key, remove the 2 screws holding the Power Box to the pole. Carefully remove the upper screw. While holding the Power Box, remove the lower screw. The Power Box can now be easily unattached from the Pole.
- Remove the upper and lower channel covers. Use an Allen key at the base of the channel covers to pry it off of the pole.
Label upper channel cover as "A" and lower channel cover as "B."
2. Remove back handles and channel covers
- Turn the unit around, so the handle is facing you
- Using the 5/32’’ Allen key untight the screws holding the handle to the pole. Remove the handle and keep it in a safe place.
- Remove the lower channel cover. Use an Allen key at the base of the channel cover to pry it off of the pole.
Label channel cover as "C."
- Using the 5/32’’ Allen key untight the screws holding the cable management handle to the pole. Remove the cable management handle and keep it in a safe place.
- Remove the lower channel cover. Use an Allen key at the base of the channel cover to pry it off of the pole.
Label channel cover as "D."
- Once channel covers and handles have been removed, your Tryten Nova Pro would look similar to the image below:
3. Resize channel covers
Once parts have been removed, using a cutter, cut the strips so that they measure according to the table below:
Channel Cover | Dimension |
A |
19 cm |
C | 24 cm |
B four pieces:
|
|
4. Install the wire storage basket accessory
The wire basket storage already has a built-in mounting bracket to attach to the pole.
- Rotate the cart so that the tablet cover is facing you.
- Install channel cover “A” at the top of the channel
- Insert two screws into the basket bracket and thread on the T-nut but do not tighten.
- Using channel cover “A” as a reference - adjust the mounting bracket to the lower section of the channel cover “A.”
- Tighten the mounting bracket into the pole when happy with the placement using the 5/32 Allen key.
- Install channel cover “D” right below the wired basket bracket.
- Install channel cover “B-4” right below channel cover “D” to completely cover the channel.
4. Adjust the universal bracket to fit the size of the tablet
- Unlock the top slider using the set of keys from the hardware pack.
- Remove the top slider from the OmniTab.
- Loosen the 3 screws using the 1/8-inch hex L key from the hardware pack.
- Pull sliders to the appropriate size tablet.
- Tight back the three adjustment screws.
- Slide the tablet into place. Insert the Top slider and push the locking button
- Connect Tablet’s charging cable
- Remove channel covers to pass the Tablet charging cable through the channel and conceal the charging cable. Make sure the cable runs all the way down to the base of the cart.
- Once the charging cable has been concealed. Tight the cart’s handle to the pole using the channel cover as a reference
5. Cable management
- Place two 2-in-1 charging station inside the wired basket. Connect the 2-in-1 charging stations to their corresponding Power adapters passing through the wire cell.
- Fit the Tablet’s charging cable inside the Power Box, passing through the upper slot
- Place the 2-in-1 charging station power adapters inside the Power Box. Pass cables through the upper slot and connect them to the 2-in-1 charging stations.
- Install channel cover “C” right below the cart handle to conceal the Tablet charging cable
- Wrap the two 2-in-1 charging stations cables inside the channel cover “B1”. Install channel cover “B1,” leaving 2 cm distance to the channel cover “C.”
- Mount the Power Box using channel cover B1 bottom as reference. Tighten the Power Box into the pole using the 5/32 Allen key.
- Install channel cover “B2” right below the Power Box
- Using Channel “B2” bottom as reference. Tight the cart’s cable management handle to the pole.
- Install channel cover “B3” right below the cable management handle
- Plug the 2-in-1 charging stations and Tablet power adaptors to the 3 Tab power extension cord
- Accommodate the Power adapters inside the Power Box
- Slide Power Box cover back into place and screw the Power Box back into place using the 2 screws and the 3/32 Allen Key. Make sure both screws are lined up properly before tightening completely.
- After following these steps, your Cart should look similar to the picture below: